RTL2832U Dongle: Setup, Software, and Specifications

Author

Reads 1.3K

Classic retro radio with vintage design, featuring an antenna for FM, AM, and SW bands.
Credit: pexels.com, Classic retro radio with vintage design, featuring an antenna for FM, AM, and SW bands.

The RTL2832U dongle is a popular tool for software-defined radio (SDR) enthusiasts. It's a small USB stick that can be used to receive a wide range of radio frequencies.

To get started with the RTL2832U dongle, you'll need to install the necessary software. The most popular software for the RTL2832U is the RTL2832U driver, which is available for download from the Realtek website.

The RTL2832U dongle has a number of key specifications, including a 1 GHz sampling rate and a frequency range of 24 MHz to 1850 MHz.

Supported Devices and Setup

The rtl2832u has a wide range of supported devices, including ezcap, Hama nano, and Terratec Noxon 1 & 2.

If you're wondering whether your device is supported, you can check the list of devices that are known to work, which includes Dexatek 1, Dexatek 2, and Dexatek 3.

Some other devices that are supported include Peak, Ardata MyVision/Gigabyte GT-U7300, and Lifeview. You can also check the main librtl2832++ source file for a full list of supported devices.

If you're still unsure, you can contact the author with information about your device, including its name, VID, PID, and tuner type. Alternatively, you can check out a helpful subreddit with a more complete list of supported devices.

Supported Devices

Vibrant close-up of green SDI cables connected to yellow device with visible USB port.
Credit: pexels.com, Vibrant close-up of green SDI cables connected to yellow device with visible USB port.

If you're looking for a device that works with the system, you're in luck - there are many supported devices out there.

The following devices are known to work: ezcap, Hama nano, Terratec Noxon 1 & 2, Dexatec 1 (also known as Logilink/MSI), and many more.

Here's a list of some of the supported devices:

  • ezcap
  • Hama nano
  • Terratec Noxon 1 & 2
  • Dexatek 1 (also Logilink/MSI)
  • Dexatek 2 (also ZAAPA HD)
  • Dexatek 3
  • Peak
  • Ardata MyVision/Gigabyte GT-U7300
  • MyGica/G-Tek
  • Lifeview
  • PROlectrix
  • Terratec Cinergy T 1
  • DIKOM HD
  • Twintech
  • Genius TVGo 2
  • SVEON

You can also check the main librtl2832++ source file for a more comprehensive list of supported devices.

Manual Override

Manual Override is a troubleshooting technique used when your device isn't recognized by the system.

If your device is missing from the device table, you can try manually overriding the recognition process. For Linux users, simply type in the VID/PID into the GRC block to override the device recognition.

In Windows, you can add the VID and PID values to the device hint by using the format 'vid=0x####pid=0x####'. This will allow the system to recognize the device.

If you're working with code, you can use the simple API to set the 'USB device override values'. This will enable the system to override the device recognition.

Credit: youtube.com, BAL EXACT-SLIDE Manual Override Procedure

Alternatively, you can add a single line to the device list in 'rtl2832.cc' to override the device recognition.

Here are the specific steps for each operating system:

USB Connection

Connecting your device via USB is a straightforward process. The device is recognised under MacOSX without any issues.

On MacOSX, the device appears in the system, ready for use.

Librtl2832++ and Software

The librtl2832++ library is a cross-platform source code that abstracts the functionality of the RTL2832U hardware. It compiles as a DLL on Windows and directly into the gr-bazbaz module for GNU Radio.

This library is highly versatile and can be reused in any other project where control of an RTL2832U-based device is needed. You can freely take the rtl2832-* files from the gr-baz lib directory and use them in your project.

I tried out two open source packages, CubicSDR and Gqrx SDR, and was successful with both. CubicSDR is particularly impressive.

Librtl2832++

Librtl2832++ is a cross-platform source code written in C++ that abstracts the functionality of the hardware (demod & tuner).

Free stock photo of aerodynamics, aerospace, antenna
Credit: pexels.com, Free stock photo of aerodynamics, aerospace, antenna

It can compile into a DLL on Windows or directly into the gr-bazbaz module for GNU Radio.

You can freely take the rtl2832-* files from the gr-baz lib directory and re-use them in any other project where you need to control an RTL2832U-based device.

Here's how librtl2832++ can be compiled:

  • as a DLL on Windows
  • directly into the gr-bazbaz module for GNU Radio

Software

I've tried out a couple of open source packages and was pleasantly surprised by the results. The first one I picked was CubicSDR, which I'm really liking right now.

Success with both open source packages I tried, including CubicSDR, is a testament to the quality and usability of these tools.

Software Defined Radios

You can use cheap DVB-T dongles as software defined radio receivers.

The RTL2832U chip is at the heart of these dongles, supporting frequency ranges that cover both VHF and UHF up to 1.7 GHz.

Antti Palosaari discovered that the RTL2832U chip can stream raw I/Q samples to the host computer.

Credit: youtube.com, BEST Software Defined Radios (SDR’s) to Buy

This discovery led to the creation of the rtl-sdr package by Steve Markgraf of OsmoSDR.

The rtl-sdr package allows you to tune the dongle and dump I/Q data to a file for post processing.

Balint Seeber created an rtl_source_c GNU Radio block in his gr-baz package to work with the rtl-sdr package.

The RTL2832U chip is more common than you might think, with some DVB-T dongles like the AGK model containing it.

The AGK model worked well on Windows but didn't work under Linux, until now.

The compatibility list in progress over at Reddit will help you find out if your specific DVB-T dongle is supported.

I2C Errors

I2C Errors can be frustrating to deal with, especially when trying to get your rtl2832u device up and running.

The rtl2832u device uses the I2C protocol to communicate with the tuner chip, which can sometimes result in errors.

One common I2C error is the "i2c_transfer failed" error, which can occur when the device is unable to communicate with the tuner chip.

Credit: youtube.com, SOFTWARE DEFINED RADIO TEARDOWN: R820/RTL2832U DECAP

This error can be caused by a faulty I2C connection or a problem with the device's firmware.

A faulty I2C connection can be caused by a damaged cable or a loose connection between the device and the tuner chip.

In some cases, the "i2c_transfer failed" error can be resolved by updating the device's firmware.

The rtl2832u device's firmware can be updated using the "rtl2832u_update" command, which can be run from the command line.

However, updating the firmware can also reset the device's configuration, so be sure to save any important settings before updating.

Direct Sampling and Specifications

Direct sampling is a viable option with the RTL2832U, allowing you to connect an antenna directly to the I input. This requires a balun to adapt the 75 ohms unbalanced antenna to the higher impedance balanced input of the RTL2832U.

A homemade toroid transformer can be used for this purpose, with a primary side of 3 to 10 turns and a secondary winding with double the number of turns, including a center tap connected to GND.

Credit: youtube.com, RTL2832U direct sampling modification

You can also use series resistors for better impedance matching.

The RTL2832U can process signals from 24MHz to 1766Mhz, making it a useful tool for signal identification.

Here are some key specifications to keep in mind:

A lowpass filter is also recommended to remove unwanted interferences from the VHF band.

Catching Sample Signals

Catching Sample Signals can be a bit of a challenge, especially when working with a device like the dongle. The dinky 5” aerial provided with the dongle is surprisingly capable.

The dongle can process signals from 24MHz to 1766Mhz. This is a pretty impressive range, and it's worth noting that the aerial has very little chance of picking out weaker signals.

The Signal Identification Guide is a great resource for trying to identify especially non-voice transmissions.

Direct Sampling

Direct sampling allows you to use the RTL2832U as is by connecting an antenna to its input.

You'll need to use a balun to adapt a 75 ohms unbalanced antenna to the RTL2832U's higher impedance balanced input.

Credit: youtube.com, RTL Direct sampling VS Quadrature sampling with upconverter

A home-made toroid transformer can work well as a balun, with a primary side that should have 3 to 10 turns.

The secondary winding should have double the number of turns as the primary, with a center tap that connects to GND.

Using series resistors for better impedance matching can also be helpful.

A lowpass filter is recommended to remove unwanted interferences from the VHF band.

Specifications

The specifications of a device like this can make or break its performance. The ADC Resolution is a mere 8 bits, which is decent but not great.

This device uses an internal oscillator clocked at 28.8 MHz, but be aware that it's expected to have large drift and phase noise. The minimum sample rate is greater than 900 ksps, and the maximum sample rate is 3.2 Msps.

You can tune a strong carrier to test the AGC, which is disabled for the E4000 but still active somewhere in the RTL2832 demod chip. The nominal sample rate is 1 Msps, but be aware that higher rates can lead to subtle signal degradation.

Credit: youtube.com, Understanding the Specifications of ADCs

Here's a quick rundown of the specifications:

Realtek

Realtek is a company from Taiwan that produces the RTL2832U digital TV demodulator.

The RTL2832U is a digital TV demodulator that supports a USB 2.0 interface and requires a front-end tuner.

It's a key component in many SDR (software defined radio) dongles, which are often found online for under $20.

These dongles usually come with a Rafael Micro R820T2 tuner front-end and a dinky antenna.

Realtek's RTL2832U chip is a crucial part of the RTLSDR design, which allows users to access signal I/Q data directly and turn it into a wideband software defined radio receiver.

Frequently Asked Questions

What is an RTL device?

An RTL device is a low-cost SDR (Software Defined Radio) receiver based on the Realtek RTL2832U chip, which can output real-time radio signal data to a computer. This versatile device was originally designed for DVB-T broadcasts, but has since been repurposed by hobbyists for a wide range of applications.

Margarita Champlin

Writer

Margarita Champlin is a seasoned writer with a passion for crafting informative and engaging content. With a keen eye for detail and a knack for simplifying complex topics, she has established herself as a go-to expert in the field of technology. Her writing has been featured in various publications, covering a range of topics, including Azure Monitoring.

Love What You Read? Stay Updated!

Join our community for insights, tips, and more.