Low-noise block downconverter Applications and Performance

Author

Reads 4.6K

A cityscape view of rooftops and satellite dish illuminated by the rising sun.
Credit: pexels.com, A cityscape view of rooftops and satellite dish illuminated by the rising sun.

Low-noise block downconverters are widely used in various applications due to their high performance and reliability. They are commonly used in satellite communications for receiving weak signals from distant satellites.

Low-noise block downconverters can operate in a wide range of frequencies, from L-band to Ka-band, and are often used in applications where high sensitivity and low noise are required. This is because they can provide a high signal-to-noise ratio, which is essential for receiving weak signals.

One of the key benefits of low-noise block downconverters is their ability to provide high gain and low noise figure, making them ideal for applications where signal strength is critical. This is particularly important in satellite communications, where signals can be weak and prone to interference.

In addition to their high performance, low-noise block downconverters are also relatively small and lightweight, making them easy to integrate into a variety of systems. This has made them a popular choice for use in a range of applications, from satellite communications to radar systems.

Here's an interesting read: Barrett Communications

Noise Figure and Selection

Credit: youtube.com, What is Low-noise block downconverter?, Explain Low-noise block downconverter

The noise figure of a low-noise block downconverter (LNB) is a critical factor in determining its overall performance. It's measured in decibels (dB) and represents the ratio of the signal-to-noise ratio (SNR) at the input to the SNR at the output.

A lower noise figure means the LNB is more efficient at converting the signal, resulting in a cleaner and stronger output signal. For example, a noise figure of 0.2 dB is considered very good, while 1 dB is average.

The selection of an LNB depends on various factors, including the frequency range, noise figure, and power consumption.

Noise Figure and Selection Guide

Noise Figure is a measure of the degradation of signal-to-noise ratio (SNR) in a system, and it's usually expressed in decibels (dB). A lower Noise Figure indicates better performance.

The Noise Figure of a receiver is determined by the noise generated by the receiver itself, as well as the noise added by the source. The Noise Figure of a source is typically lower than that of a receiver.

A Noise Figure of 3 dB or less is considered excellent, while a Noise Figure of 10 dB or more is considered poor.

10.75

Credit: youtube.com, Understanding Spectrum Analyzers – Noise Figure

10.75 GHz LO instability is a notable factor in the performance of a Low Noise Block Down Converter. It can vary by as much as ± 150 kHz.

A 10.75 GHz Ku-band LNB PLL LO has a single LO frequency of 10.75 GHz and a single 75 Ohm F-type output. The output power of this device is +3 dBm at the 1 dB compression point.

This specific LNB PLL LO has a gain of 45 dB and a noise figure of 0.9 dB.

X Band

X Band is a type of frequency conversion technology used in satellite systems.

UMT LLC offers exceptional X-Band LNBs that convert frequencies from 8-12 GHz to 950-1950 MHz.

These converters are designed to optimize satellite reception and provide top-notch performance.

X-Band LNBs are a crucial component in satellite systems, ensuring seamless communication and data transfer.

UMT LLC's X-Band LNBs are a reliable choice for those seeking high-quality satellite solutions.

Additional reading: Low Voltage Systems

Communication Systems

Credit: youtube.com, Low Noise Blocks (LNBs): Crucial Specifications You Need to Know | MPT

Communication Systems are crucial for Low-Noise Block Downconverters (LNBs) to function properly.

The LNB uses a communication system to receive and process signals from satellites in geostationary orbit, which are typically 36,000 kilometers away from Earth.

A key feature of communication systems used in LNBs is the ability to handle high-frequency signals, such as those in the Ka and Ku bands.

These systems use a combination of amplifiers and filters to reduce noise and interference in the signals.

The communication system in an LNB also includes a frequency converter, which changes the signal's frequency to a lower one that can be easily processed by the LNB's electronics.

This conversion process helps to reduce noise and interference in the signal, allowing for clearer and more reliable communication.

Readers also liked: S Band

UMT LLC

UMT LLC offers a wide range of low-noise block converters (LNBs) that cater to various satellite communication bands, including C-Band, X-Band, Ku-band, K-band, and Ka-band.

Their products provide full coverage from standard C-band (4-8 GHz) to the highest Ka-band (26.5-40 GHz). This makes them an excellent choice for professional broadcasting and VSAT use.

You might like: C Band (IEEE)

Grey and Black Transistor Radio
Credit: pexels.com, Grey and Black Transistor Radio

UMT LLC's LNBs boast exceptional performance, with a low noise figure of 0.3–0.7 dB, high gain of 55–65 dB, and strong frequency stability. This is ideal for applications that require high signal quality.

You can choose between PLL LNB with 10 MHz external reference or DRO-based models for more basic applications, depending on your specific needs.

Their products also offer customization options, including special connectors, specific LO frequencies, and ruggedized versions. This flexibility is a major advantage for clients with unique requirements.

Here are some key benefits of buying LNBs from UMT LLC:

  • Quality products at competitive prices
  • Worldwide delivery, including the USA, India, Europe, Africa, and beyond
  • Comprehensive catalog featuring a wide range of LNB options
  • Expert support and top-notch customer service for all your LNB requirements
  • Meaningful cost-effective choices for all your frequency, noise, and amplifier needs
  • Tailored solutions for specific satellite frequency bands and signal receiver requirements
  • Detailed product specifications to aid in your purchasing decisions

UMT LLC also provides global delivery and support, shipping worldwide and offering fast processing, documentation, and technical advice to their B2B clients.

LNA and LNA

LNA and LNA is a crucial component in the Low-noise block downconverter. The LNA (Low Noise Amplifier) is designed to amplify the weak RF signal while minimizing noise.

The LNA is typically placed at the front end of the downconverter to ensure optimal signal quality. It's usually implemented in the form of a monolithic microwave integrated circuit (MMIC).

A good LNA can provide a noise figure as low as 0.5 dB, which is essential for sensitive RF applications. This is achieved through advanced design techniques and careful selection of components.

Difference Between LNA and LNA

Closeup Photography of Radio Receiver
Credit: pexels.com, Closeup Photography of Radio Receiver

The difference between LNB and LNA is quite clear. An LNB is specifically designed to operate at very low frequencies used for satellite reception.

An LNA, on the other hand, is more broadly used in various communication systems.

While both are amplifiers, they serve different purposes.

An LNB is designed for satellite reception, whereas an LNA is used in a range of applications.

In essence, LNBs are specialized for satellite use, whereas LNAs are more versatile.

11.30

11.30 GHz is a specific frequency used in the Ku-band LNB PLL LO, which is a Low Noise Block Down Converter with a single LO frequency of 11.30 GHz.

This frequency has a relatively low LO instability of ± 150 kHz.

The Ku-band LNB PLL LO also features a 45 dB gain, making it a powerful signal amplifier.

The noise figure of this device is a low 0.9 dB, which is a measure of the signal-to-noise ratio.

The output power of the Ku-band LNB PLL LO is +3 dBm, which is a relatively low power output.

This low power output is typical of LNBs, which are designed to amplify weak signals from satellites rather than generate high power signals.

Dual Pol with Stacked Outputs

Credit: youtube.com, Feature: Modelithics Models for PA and LNA Design

Dual polarisation LNBs can be arranged to support two alternative polarisations, such as vertical or horizontal, or left hand or right hand circular polarisation.

Dual polarisation LNBs can be switched remotely using two alternative DC supply voltages, like 13 volts for vertical polarisation and 19 volts for horizontal polarisation.

The DC supply voltage for dual polarisation LNBs is not always fixed, as it can vary depending on the specific model and intended use.

Dual polarisation LNBs with stacked outputs have a gap in the output spectrum, making it easier to combine filters and avoid interference and noise.

Note that LNBs may fail on one polarisation or on one frequency band, and the failure mode may only occur at certain temperatures.

The DISH-PRO system uses stacked blocks of frequencies in the LNB output, one block from each polarisation, allowing for simultaneous availability of all signals at the set top box end.

For more insights, see: B and O Telephone

Satellite Systems

Satellite Systems are used to transmit and receive signals from satellites orbiting the Earth. They are composed of a combination of ground equipment and space-based components.

Credit: youtube.com, LNB Low Noise Block Downconverter for a FTA Satellie Dish

The ground equipment includes the Low-noise block downconverter (LNB) which is a crucial part of the satellite system. LNBs are used to convert the high-frequency signals received from the satellite into lower frequency signals that can be processed by the receiver.

The LNB is typically installed on the satellite dish and is connected to the receiver via a cable. This cable is usually a coaxial cable and is designed to minimize signal loss and interference.

Satellites in geostationary orbit are used in many satellite systems, including those that utilize LNBs. These satellites are positioned at an altitude of approximately 36,000 kilometers above the equator.

The LNB is designed to operate in a specific frequency range, typically between 10.7 and 12.75 GHz. This range is chosen to minimize interference with other satellite systems and to ensure optimal signal reception.

You might like: Cable Protection System

Supply Voltages

Supply Voltages are typically in the 13v to 19v range, and can be fed up the cable to the LNB.

Credit: youtube.com, Ku Band Satellite LNB’s -how they work and Frequency Setting

Changing the supply voltage can sometimes alter the polarization of the LNB, but this is less common.

Both the inner and outer conductors must make good electrical contact to prevent corrosion and ensure proper function.

High resistance between the conductors can cause the LNB to switch permanently into the low voltage state, leading to signal deterioration.

Poor connections amongst multiple cables can cause the wrong voltage to be applied to the LNB and other modules, leading to peculiar effects.

Earth loop currents, which can be caused by 50 Hz or 60 Hz mains currents on the outer conductors, can also be a problem.

It's essential to be cautious when physically troubleshooting a system, as electrical antenna contacts between the BUC chassis and LNB can be tricky to navigate.

The quality and smoothing of the DC supplies used for the LNBs is also of great importance, as it can affect the overall performance of the system.

Ku-Band

Credit: youtube.com, Design of Ku band SATCOM Low Noise Block Down Converter, with RF Systems and Circuits modeling

Ku-Band is a popular choice for satellite communications, and for good reason. It offers high-quality products with extended durability and performance standards.

One of the key benefits of Ku-Band is its competitive pricing, with special offers available for Ku-Band LNBs. You can get the best value for your money without sacrificing performance.

UMT LLC offers a comprehensive catalog showcasing various Ku-Band LNB types and specifications. This makes it easy to find the right product for your specific needs.

If you're looking for a tailored solution for a specific satellite frequency band or reception requirement, UMT LLC has got you covered. They offer customized solutions to fit your unique needs.

Their products also come with universal bracket modifications to fit diverse dish setups. This ensures a seamless installation process.

Ku-Band LNBs from UMT LLC also enhance digital signal reception for an immersive viewing experience. You'll get the best possible picture quality without any interference.

Recommended read: Ku Band

Credit: youtube.com, What kind of LNB should I use on my KU Band Satellite Dish? FTA Satellite TV

Here's a brief overview of the benefits of Ku-Band LNBs from UMT LLC:

  • High-quality products with extended durability and performance standards
  • Competitive prices and special offers for Ku-Band LNBs
  • Global delivery options, reaching the USA, India, Europe, Africa, and beyond
  • Tailored solutions for specific satellite frequency bands and reception requirements
  • Exceptional customer support and detailed product specifications
  • Universal bracket modifications to fit diverse dish setups
  • Enhanced digital signal reception for an immersive viewing experience

Dual Band

Dual-band LNBs are a type of low-noise block downconverter that can receive signals from two different frequency bands.

Ku band LNBs typically have two alternative local oscillator frequencies, for example 9.75 GHz and 10.6 GHz.

The higher frequency option is selected using a 22 kHz tone injected into the cable.

Such an LNB may be used to receive 10.7 - 11.7 GHz using the lower 9.75 GHz LO frequency.

The higher band 11.7 - 12.75 GHz can be received using the higher 10.6 GHz LO frequency.

A few Ka band LNBs may have as many as 4 local oscillator frequencies.

Frequency Stability

Frequency stability is crucial for satellite TV reception, and LNBs use dielectric resonator stabilised local oscillators to achieve this. These DROs are relatively small and can resonate at the required frequency, but they can be quite unstable with temperature and frequency accuracies may be +/- 250 kHz to as much as +/- 2 MHz at Ku band.

Credit: youtube.com, Part 1: Design of K/Ka Band SATCOM Low Noise Block Down Converter (LNB)

This variation can be a problem for narrow carriers, like 50 kHz wide, as the indoor receiver may not find the carrier at all or may even find the wrong one. Most TV carriers, however, are quite wide bandwidth, like 27 MHz, so even with 2 MHz error, the indoor receiver will successfully tune the carrier and capture it within the automatic frequency control capture range.

If you want to receive narrow carriers, you'll need a rather clever receiver that will sweep slowly over a range like +/- 2 MHz searching for the carrier and trying to recognise it before locking on to it. Alternatively, you can buy Phase Lock Loop LNBs which have far better frequency accuracy and are more expensive.

Phase Lock Loop LNBs can be internal, using a crystal oscillator in the LNB, or external, relying on a 10 MHz reference signal sent up the cable by the indoor receiver. The benefit of using an external reference PLL LNB is that the indoor reference oscillator is easier to maintain at a stable constant temperature.

Phase Noise

Credit: youtube.com, Low-noise block downconverter

Phase noise is a crucial aspect to consider when it comes to LNB performance.

Modern DRO LNBs are designed to have good phase noise performance, often marketed as 'digi-ready'.

However, their phase noise is still worse than that of PLL LNBs.

For digital TV carriers, good phase noise performance is particularly important for low bit rate and high spectral efficiency modulation methods like 8-PSK, 8-QAM, or 16-QAM modulation.

10.60

The 10.60 GHz frequency is used in some Ku-band LNBs, like the one mentioned in Example 2, which has a single LO at 10.60 GHz and a 75 Ohm F-type output.

This LNB has a relatively high LO instability of ± 150 kHz, which can impact its overall performance.

The gain of this LNB is 45 dB, which is a decent level for receiving weak signals.

A noise figure of 0.9 dB is quite good, indicating that the LNB is doing a good job of minimizing noise in the signal.

The output power P1dB of +3 dBm is a reasonable level, indicating that the LNB is producing a decent amount of power for the signal.

On a similar theme: Block Level Storage

Phase Noise

Credit: youtube.com, Understanding Phase Noise Fundamentals

Phase noise is a critical factor in satellite TV reception. All modern DRO LNBs are sold as 'digi-ready', which means some attention has been paid to keeping the phase noise down.

The phase noise of DRO LNBs is still far worse than for PLL LNBs. This is because PLL LNBs have better quality oscillators in both the transmit and receive chains.

For low bit rate digital carriers, good phase noise performance is really needed. This is because these carriers require more power from the satellite and a bigger receive dish.

Digital carriers using high spectral efficiency modulation methods like 8-PSK, 8-QAM or 16-QAM modulation also require good phase noise performance. These methods reduce the bandwidth required but need more power and a better quality PLL type oscillator in the receive chain.

Feedhorns and Quattro Universal

DBS dishes use an LNBF, which matches the antenna's feedhorn up with the LNB. This is a crucial component for receiving satellite TV signals.

Credit: youtube.com, Universal LNBs - Overview

A small diplexer is often used to distribute the resulting IF signal, typically in the 950 MHz to 1450 MHz range, and "piggyback" these signals with the same TV cable that carries lower-frequency terrestrial television signals from a typical outdoor antenna.

The TV set receiver also has another diplexer that separates the signals.

The Quattro Universal LNB is a 4-output LNB designed for use as a "head end" I.F. distribution system. This makes it ideal for apartment complexes.

Here are the 4 outputs of the Quattro Universal LNB:

  • Low band horizontal polarization
  • High band horizontal polarization
  • Low band vertical polarization
  • High band vertical polarization

LNBs can generally supply up to 16 outputs for separate dwellings or Digiboxes.

11.80

11.80 GHz is a specific frequency used in the Ku-band LNB PLL LO, which is a type of Low Noise Block Down Converter.

The Ku-band LNB PLL LO has a single LO frequency of 11.80 GHz, and it also has a single 75 Ohm F-type output.

This frequency has an LO instability of ± 150 kHz, which is a measure of how stable the local oscillator is.

Closeup of detail of retro radio receiver with control panel placed on table in cozy flat
Credit: pexels.com, Closeup of detail of retro radio receiver with control panel placed on table in cozy flat

The Ku-band LNB PLL LO has a gain of 45 dB, making it suitable for use in a variety of applications.

A noise figure of 0.9 dB is achieved with this device, which is a measure of its ability to minimize noise in the signal.

The output power P1dB is +3 dBm, which is a measure of the device's ability to amplify the signal.

Expand your knowledge: Integrated Access Device

Feedhorns

Feedhorns are a crucial component in DBS dishes, matching the antenna's feedhorn up with the LNB.

DBS dishes use an LNBF, which is essentially a combination of a feedhorn and an LNB.

The feedhorn in an LNBF is designed to receive the satellite signal and direct it to the LNB.

A small diplexer is often used in LNBFs to distribute the resulting IF signal, typically in the 950 MHz to 1450 MHz range.

This IF signal is then "piggybacked" with the same TV cable that carries lower-frequency terrestrial television signals from a typical outdoor antenna.

The TV set receiver also has a diplexer that separates the signals, ensuring that the correct signal is received by the viewer.

Quattro Universal

Credit: youtube.com, Gardiner Ku Universal High Band Ultra Low Noise Figure LNB

The Quattro Universal LNB is a type of LNB designed for use as a "head end" I.F. distribution system, typically used in apartment complexes. It has four outputs.

These outputs are specifically configured to provide separate channels for low and high band polarization in both horizontal and vertical orientations. The four outputs are:

  • Low band horizontal polarization
  • High band horizontal polarization
  • Low band vertical polarization
  • High band vertical polarization

Quattro Universal LNBs are designed to work with standard circular or offset focus dishes, but dishes that are wider than they are tall require a special LNB.

DROs, or dielectric resonator stabilized local oscillators, are used in LNBs to provide frequency stability, but they can have tolerances of up to +/- 250 kHz to 2 MHz in Ku band.

Testing and Overloading

Overloading an LNB can be a real issue, especially if you have a large dish and are receiving signals from a satellite intended for smaller antennas. This can cause a 20 dB increase in total power of the signals into the LNB, which may be sufficient to overload some of the transistor amplifier stages inside.

Credit: youtube.com, Teardown: Ku Band Satellite TV LNB

Measuring the composite output power of the LNB using a power meter is a good way to check for overloading. Compare this reading with the -1 dB compression point in the manufacturer's specification to see if you're within safe limits.

If you're concerned about overloading, consider using a special low gain or high power output level LNB, or doing an antenna pattern test on both a high power and a low power satellite.

The band 3.625 - 4.2 GHz is under increasing pressure from other spectrum users like WiFi and WiMAX, which can interfere with your LNB. Using a band pass filter in front of your LNB can help restrict the range of frequencies you can receive.

Here are some steps to check the performance of your LNB:

  • Check the ammeter drawing the DC current from the power supply (approx. number of mA’s provided by the manufacturer).
  • Poor quality (or corroded) F type connections are the most typical cause of concern.
  • The center pin (of the F connector plug) should stick out ~ 2mm, away from the surrounding ring.
  • A satellite finder power meter is also helpful.

8.80

The 8.80 GHz frequency is used by a Ku-band LNB PLL LO, which has a single LO frequency of 8.80 GHz and a single 75 Ohm F-type output.

Credit: youtube.com, Current Overload Wiring Testing

This LNB has a LO instability of ± 150 kHz, which can affect its performance in certain situations.

The gain of the 8.80 GHz LNB is 45 dB, making it suitable for applications where a strong signal is required.

A noise figure of 0.9 dB is quite low, indicating that the LNB is designed to minimize signal degradation.

The output power of the 8.80 GHz LNB is +3 dBm, which is a relatively low power level.

Testing an

Testing an LNB is crucial to ensure it's working correctly and efficiently. Poor quality or corroded F-type connections are the most typical cause of concern, so make sure to check them first.

To do this, check the ammeter drawing the DC current from the power supply, which should be around the number of mA's provided by the manufacturer. A satellite finder power meter is also helpful, especially when pointing the LNB up at outer space (clear sky), where the noise temperature contribution from the surroundings becomes negligible.

Retro audio equipment old tube amplifier radio illuminated scale.
Credit: pexels.com, Retro audio equipment old tube amplifier radio illuminated scale.

The meter reading will directly correspond to the LNB's noise temperature. For example, if pointing the meter to outer space reads 100K, then pointing the LNB towards the ground (say at a temperature of approximately 300K) should increase the noise power meter reading to roughly 400K (100K + 300K).

If you notice any inconsistencies in your LNB's performance, it may be due to LO instability, which can be a problem with some LNBs, especially those with a single LO frequency like the Ku-band LNB PLL LO 8.80, which has a LO instability of ± 150 kHz.

To troubleshoot, you can try checking the supply voltage and the transmit reject filter, as continuously blowing up LNBs can get cost prohibitive quite rapidly.

Linear and Supply Power

The DC voltage power supply is fed up the cable to the LNB, and often altering this voltage can change the polarization or frequency band. Voltages are normally 13 volts or 19 volts.

Credit: youtube.com, LANZ TV Troubleshooting of Signal quality and LNB power supply.

Perfect weatherproofing of the outdoor connector is essential to prevent corrosion, and both the inner and outer conductors must make good electrical contact to avoid high resistance. High resistance can cause the LNB to switch permanently into the low voltage state.

The quality and smoothing of the DC supplies used for the LNBs are of great importance, and it's also crucial to be aware of electrical connections at the antennas between the LNB and the BUC chassis, which can be indeterminate and depend on screws in waveguide flanges.

Linear

Linear systems are often used in satellite communications, and one key component is the Linear LNB, which is essentially an amplifier on the end of a satellite dish.

A Linear LNB is designed to amplify weak satellite signals, allowing for clearer reception.

This type of LNB is commonly used in satellite TV systems, where a strong signal is crucial for receiving high-quality broadcasts.

The Linear LNB is typically powered by a separate power source, which is usually included in the system.

Supply Power

Modern 850W power supply unit with 80 Plus Gold certification, ideal for gaming PCs.
Credit: pexels.com, Modern 850W power supply unit with 80 Plus Gold certification, ideal for gaming PCs.

Supply power is crucial for your LNB, and it's essential to get it right. The DC voltage power supply is fed up the cable to the LNB, and it's often possible to change the polarization by altering this voltage.

Typically, the DC supply is in the 13v to 19v range. Both the inner and outer conductors must make really good electrical contact, otherwise corrosion is rapid.

High resistance can cause the LNB to switch permanently into the low voltage state, and high resistance can also lead to overall signal deterioration. This can be a problem if the electrical connections at the antennas between the LNB and the BUC chassis are not made correctly.

If you're physically trouble shooting a system, be aware that the electrical antenna contacts between the BUC chassis and LNB are often difficult to navigate. Earth loop currents may also be a problem, and it's possible to find 50 Hz or 60 Hz mains currents on the outer conductors.

The quality and smoothing of the DC supplies used for the LNBs are also of great importance. Perfect weatherproofing of the outdoor connector is essential to prevent corrosion.

Frequently Asked Questions

What does LMB stand for on a satellite?

The LNB on a satellite dish stands for Low-Noise Block downconverter, containing electronic components that receive and process signals. This crucial part is usually located at the front of the metal arm.

Danny Orlandini

Writer

Danny Orlandini is a passionate writer, known for his engaging and thought-provoking blog posts. He has been writing for several years and has developed a unique voice that resonates with readers from all walks of life. Danny's love for words and storytelling is evident in every piece he creates.

Love What You Read? Stay Updated!

Join our community for insights, tips, and more.