
Digital I/O is the backbone of any industrial automation system, and understanding its basics is crucial for any engineer or technician. Digital I/O refers to the input and output of digital signals between a control system and external devices.
A digital signal is a binary signal that can only be in one of two states: high or low. This is in contrast to analog signals, which can take on any value within a given range. In digital I/O, the signal is typically represented by a voltage level, with high being above a certain threshold and low being below.
In a typical digital I/O system, you'll have a mix of input and output devices. Input devices, such as sensors, convert physical parameters into digital signals, while output devices, like actuators, convert digital signals into physical actions.
Digital I/O Basics
To access digital I/O, you'll need to use the digitalio module, which provides classes for basic digital IO. This module changes hardware state and should be deinitialized when it's no longer needed.
A DigitalInOut object is used to digitally control I/O pins. It defaults to input with no pull, but you can change the direction with switch_to_input() and switch_to_output().
You can set the drive mode and value with the switch_to_output() method, and the pin drive mode is one of two options: PUSH_PULL or OPEN_DRAIN.
Here are the possible drive modes:
- PUSH_PULL
- OPEN_DRAIN
When using a Raspberry Pi RP2350 A2, be aware that there's a GPIO hardware issue that causes excessive leakage current. This can cause a pin to read as high even when driven or pulled low. To prevent this problem, drive the input pin with a strong signal that can overcome the leakage current, or use a strong external pull-down resistor of 8.2k ohms or less.
What's the Difference?
Analog signals are continuous electrical signals that flow seamlessly from one point to another. They're like a smooth, uninterrupted stream.
On the other hand, digital signals are non-continuous electrical signals, transmitted as a series of distinct, separate signals. This is a fundamental difference between the two.

Many everyday devices rely on analog signals, including televisions, radios, and microphones. These devices use continuous signals to transmit information.
In contrast, digital devices like computers, smartphones, and televisions (yes, most modern TVs are digital!) use non-continuous signals to transmit information. This is a key reason why digital signals are more resistant to interference.
Here's a quick comparison of analog and digital signals:
Analog signals are still widely used in many applications, including audio equipment and medical devices. However, digital signals have become increasingly popular due to their efficiency and reliability.
Basic Pin Support
Digital I/O basics start with understanding how to control digital pins. This involves using classes from the digitalio module.
To use digital pins, you need to create a DigitalInOut object associated with the pin. This defaults to input with no pull, but you can change the direction using switch_to_input() and switch_to_output().
Deinitializing digital pins is crucial when you're done using them. This prevents hardware issues and ensures the program runs smoothly. You can either call deinit() or use a context manager to achieve this.
Digital pins have specific limitations, especially on Raspberry Pi RP2350 A2 stepping. Excessive leakage current can cause issues, making it difficult to read values accurately. To prevent this, drive the input pin with a strong signal or use an external pull-down resistor with a value of 8.2k ohms or less.
Digital pins can be configured in different drive modes. The two main options are PUSH_PULL and OPEN_DRAIN. Understanding these modes is essential for working with digital pins.
Here's a summary of the drive modes:
Digital pins also have pull configurations for input. The two main options are UP and DOWN. Understanding these configurations is essential for working with digital pins.
Choosing the Right Device
The first step in implementing digital I/O is to choose the right device for your application. This involves considering factors such as the type of signal you need to transmit, the level of noise immunity required, and the available power supply.

For example, a digital I/O module with a high level of noise immunity is essential for applications where the signal is prone to interference.
In general, a digital I/O module with a high sampling rate is ideal for applications that require real-time data transfer.
A good rule of thumb is to choose a device with a sampling rate that is at least 10 times faster than the maximum rate at which data is transferred.
Digital I/O devices with built-in signal conditioning are also useful for applications where the signal needs to be filtered or amplified.
PXI/PXIe Modules
PXI/PXIe modules offer a range of digital I/O options for various applications.
Some modules are designed for high-density digital input, like the 32-channel 50V PXI/PXIe High Density Digital Input Module.
This type of module is ideal for applications that require a large number of digital inputs, such as data acquisition or control systems.
The 40/42-412A is a digital output module with high-side or low-side drive capability, making it suitable for applications where a high current is required.
This module's high-side or low-side drive capability allows for flexibility in system design and configuration.
PXI/PXIe modules can be programmed to meet specific application requirements, such as the PXI/PXIe Digital Input Module with Dual Programmable Threshold Settings.
Design and Architecture
Designing a digital I/O system from scratch can be a daunting task, but knowing the right architecture to use can make all the difference. Our portfolio of I/O architectures offers a wide range of solutions for programmable logic controllers (PLCs) and industrial control systems.
You can choose from isolated or non-isolated architectures, depending on your specific needs. Our high-side and low-side portfolios offer competitive solutions for driving and protecting loads.
When selecting an I/O architecture, consider the type of loads you'll be driving. For example, our high-side switches can drive resistive, capacitive, or inductive loads, and even offer 60V operating voltage tolerance.
Here are some key features to look for in a high-side switch:
- Adjustable current limit
- Output clamp to demagnetize inductive loads
- Wire-break and short-to-supply detection
- Accurate current sensing and ADC
On the other hand, low-side switches are ideal for applications that need to convert a digital signal into an analog output. They provide a redundant path to the load, with fault tolerance and can handle high currents and voltages up to 70V.
Our low-side switch design also offers high reliability, low power consumption, and optional external clamps for easy integration.
Featured Reference Designs
Digital I/O is a crucial aspect of modern automation systems, and having the right reference designs can make all the difference.
Digital Output Modules are a standard component in a PLC/PAC or DCS to control actuators, motors and other resistive, capacitive or inductive loads.
A key benefit of digital output modules is that they often come with integrated protected low side drivers, making the MCU interface easy to test.
These protected low side drivers can handle a variety of loads, including resistive, capacitive, and inductive types.
By using a parallel interface, customers can take advantage of a simplified MCU interface, making it easier to integrate with other system components.
Related reading: Web and Digital Interface Designers
Frequently Asked Questions
What is a digital io?
A digital I/O (Input/Output) is an interface that connects a computer to external devices, allowing it to read and write digital signals. This enables monitoring and control of various devices, such as sensors and relays, in control circuits and systems.
What are examples of io devices?
Examples of input devices include keyboards, mice, and microphones, while output devices include speakers, monitors, and printers. These devices enable computers to interact with users and display information.
Featured Images: pexels.com


