60-meter band Frequency and Propagation Explained

Author

Reads 2.9K

Long exposure of a night sky featuring an antenna with star trails and clouds.
Credit: pexels.com, Long exposure of a night sky featuring an antenna with star trails and clouds.

The 60-meter band is a fascinating realm of amateur radio operation, with its unique frequency allocation and propagation characteristics. The 60-meter band spans from 5.3515 to 5.4065 MHz.

This band is allocated for amateur radio use, specifically for the 5 MHz range. The 60-meter band is a relatively narrow band, which can be both a blessing and a curse for operators.

Propagation on the 60-meter band is influenced by the Earth's ionosphere, particularly the D-layer, which can cause signal loss and absorption. This can lead to unpredictable and variable propagation conditions.

Recommended read: Base Band 5

Band Allocations

The 60-meter band has a unique allocation system, and understanding it is crucial for amateur radio operators.

The International Telecommunication Union (ITU) Region 1 countries, such as North Macedonia and the United Kingdom, have allocated blocks of frequencies for amateur radio use, rather than dedicated channels. These blocks can be up to 5 kHz wide and are allocated by the national telecommunications regulator.

Credit: youtube.com, Understanding the 60 meter band channels (Part 1)

In the United States, the Federal Communications Commission (FCC) has allocated the 60-meter band with a specific band plan, which includes channelized USB and a power limit of 100 W ERP.

Canadian amateur radio operators have four fixed frequencies on which they can operate, plus a 15 kHz-wide band, but must ensure that their emissions do not exceed 2.8 kHz in bandwidth.

To avoid causing harmful interference, amateur radio operators must give way to senior users on these frequencies. This means that Canadian operators must use CW, SSB, and narrow-bandwidth digital modes, but not AM or FM.

Here is a list of the channel-centre frequencies allocated by Industry Canada for the Amateur Radio Service in Canada:

  • 5332 kHz
  • 5348 kHz
  • 5358.5 kHz
  • 5373 kHz
  • 5405 kHz

Amateur radio operators should tune 1.5 kHz below these centre-channel frequencies to be "on channel" using USB and Pactor III.

For your interest: 630-meter Band

Channel Allocations

The 60-meter band has five fixed frequencies allocated for Amateur Radio use in Canada. These frequencies are 5332, 5348, 5358.5, 5373, and 5405 kHz.

Credit: youtube.com, Understanding the 60 meter band channels (Part 2)

Each of these frequencies has an effective bandwidth of 2.8 kHz, which means you need to be precise with your tuning. To be on the right frequency, you should tune 1.5 kHz below the centre-channel frequency using USB and Pactor III.

The centre-channel frequencies are the ones you'll use for CW or PSK31, while for SSB, upper sideband will be the convention to follow on the 60m band.

Propagation and Power

The 60-meter band is a reliable choice for local-to-medium distance communications, especially when 80 or 40 m frequencies are unavailable.

This band is less affected by D-Layer absorption than 80 m, making it an ideal candidate for near vertical incidence skywave (NVIS) communications.

NVIS is a technique that provides seamless local-to-medium distance HF communications, and it's often used in emergency communication scenarios where normal communications infrastructure is lacking.

Propagation Characteristics

The 60-meter band forms a communication bridge between 0-650 km, often needed in emergency scenarios where normal communications infrastructure is down.

Credit: youtube.com, Propagation characteristics of EM wave - OBE

The 60-meter band is less affected by D-Layer absorption than the 80-meter band.

Propagation effects can make use of the 80 or 40-meter band impossible for local-to-medium distance communications, making the 60-meter band a reliable option.

Information about the critical frequency (foF2) of the ionosphere is highly important for setting up reliable NVIS radio links.

Ionograms produced by local ionosondes can be found online to obtain this information.

The 60-meter band is an ideal candidate for near vertical incidence skywave (NVIS), a technique used for seamless local-to-medium distance HF communications.

Combien De Puissance

In Canada, amateur radio operators are limited to a maximum of 100 watts of power, which is equivalent to 100 watts emitted by a dipole antenna. If your antenna has more gain than a dipole, you'll need to reduce your power accordingly to stay within the limit.

The 100 watt limit in Canada is quite generous, and most countries actually cap amateur radio operators at 15 watts of equivalent isotropic radiated power (EIRP).

Frequency and Channels

Credit: youtube.com, Accessing the 60 Meter Channels in the Yaesu FT-891

The 60-meter band has some unique frequency and channel rules to keep in mind. The band is allocated for Canadian Amateurs who hold an Advanced certificate, or a Basic with Honours or Basic with 5 wpm Morse Code qualification.

To ensure you're on the right frequency, you need to understand the difference between your suppressed carrier radio frequency and your audio frequency bandwidth. The channels allocated by Industry Canada for the Amateur Radio Service are 5332, 5348, 5358.5, 5373, and 5405 kHz, which are channel-centre frequencies.

When operating SSB, the convention is to use Upper Sideband (USB) on 5 MHz. To be "on channel" using USB and Pactor III, you should tune 1.5 kHz below the centre-channel frequencies. Here are the specific frequencies to use for each mode:

Remember, digital mode activity, including FT8, is centred on 5357 kHz, and you should set your transceiver to this frequency while using USB to transmit digital data.

Staying on Frequency

Credit: youtube.com, Frequency Bands & Channel Bandwidth | Telecoms Bytes - Mpirical

Staying on Frequency is crucial for Amateur Radio operators. You need to know the correct frequencies to use, depending on your mode of operation.

If you're using CW, you can set your transceiver to any of the following frequencies: 5332 kHz exactly, 5348 kHz exactly, 5351.5 to 5366.5 kHz, 5373 kHz exactly, or 5405 kHz exactly.

For SSB, the convention is to use Upper Sideband (USB) on 5 MHz. If you're using digital modes like FT8, you should also use the USB mode on your transceiver.

Here are the frequencies you can use for USB voice or digital modes: 5330.5 kHz exactly, 5346.5 kHz exactly, 5351.5 to 5363.7 kHz, 5371.5 kHz exactly, or 5403.5 kHz exactly.

Note that digital mode activity, including FT8, is centered on 5357 kHz. This is the frequency to which you should set your transceiver while using USB to transmit digital data.

In the US, channelized USB is mandatory on the 60-meter band. This means you need to use a specific frequency, and the USB suppressed carrier frequency (or "dial" frequency) is normally 1.5 kHz below the quoted channel frequency.

Here are the modes permitted on the 60-meter band in the US: USB Voice, CW, RTTY, and Data (including digital modes like FT8 and others).

For your interest: 60 Seconds

Radio Band Channels

Credit: youtube.com, Understanding the Radio Frequency Spectrum (#715)

The 60m Amateur Radio Band Channels are a great place to start exploring the world of amateur radio. The channels are allocated by Industry Canada and are available to anyone holding an Advanced certificate, or anyone holding a Basic with Honours or Basic with 5 wpm Morse Code qualification.

Each channel has an effective bandwidth of 2.8 kHz, which is important to keep in mind when operating on the 60m band. To ensure you're on the right frequency, you need to tune to the channel-centre frequency, which is 1.5 kHz below the centre-channel frequency for USB and Pactor III modes.

The channel-centre frequencies for the 60m band are 5332, 5348, 5358.5, 5373, and 5405 kHz. These are the frequencies you should aim for when operating on the 60m band. However, if you're using SSB, you'll need to tune to the upper sideband (USB) frequency, which is 1.5 kHz below the channel-centre frequency.

Credit: youtube.com, Radio Frequencies, Bands, Modes and Bandwidth Explained.

Here's a summary of the channel-centre frequencies for the 60m band:

It's also worth noting that digital modes, such as FT8, should be centred on 5357 kHz, and should be transmitted using the USB mode.

Country-Specific Information

North Macedonia has issued permission for 14 frequency blocks between 5250 and 5450 kHz with 100 W voice, CW, and data, granted until 30 January 2017.

The UK was allocated 11 frequency blocks of varying bandwidths in January 2013.

RSM, the Macedonian national amateur radio society, had originally requested permission for a small group of dedicated radio amateurs, but the permission was given to the organisation, which may be modified in the future.

These blocks in North Macedonia are mostly 5 kHz-wide, allowing for a range of amateur radio activities.

Beacons and Updates

The 60-meter band has a number of beacons that can be useful for amateur radio operators. These beacons transmit on specific frequencies and can provide valuable information about propagation and other factors.

Credit: youtube.com, LX0HF - 60 meter band beacon - 5205.25 kHz

One example is the DRA5 beacon in Germany, which transmits on 5195.0 kHz and provides propagation information in CW, PSK31, and RTTY modes. It's a great resource for understanding how signals propagate.

Some beacons are active only during certain times of the year. For example, the DRA5 beacon in Germany transmits from 0400 to 2200 UTC during summertime and 0500 to 2300 UTC during wintertime.

Here are some key frequencies for beacons in the 60-meter band:

Keep in mind that some beacons may not be active at all times, so it's a good idea to check their schedules and frequencies before attempting to contact them.

Beacons

Beacons are a fascinating aspect of amateur radio, and I'm excited to share some interesting facts with you. Beacons are essentially transmitters that broadcast information to help amateur radio operators and researchers study propagation, a term that refers to how radio signals travel through the atmosphere.

Credit: youtube.com, HOVERAir Beacon and Joystick Tutorial

Germany has a propagation information beacon that transmits on 5195.0 kHz, which is a frequency that's perfect for studying propagation patterns. This beacon is particularly useful during summertime, when it transmits from 0400 to 2200 UTC.

Some beacons are quite strong, like the one in Luxembourg, which broadcasts at 5 W EIRP (Effective Isotropic Radiated Power). This is a significant amount of power, and it's interesting to note that the beacon transmits continuously, with callsign identification every minute.

Did you know that some beacons transmit different types of signals? For example, the South African Amateur Radio League has a beacon that transmits in WSPR (Weak Signal Propagation Reporter) mode, which is a mode that's specifically designed for experimental purposes.

If you're interested in knowing more about the beacons, here's a quick rundown of some of the notable ones:

Meters and Updates

The 60-meter band has been a game-changer for amateur radio enthusiasts. First introduced in 2002, it was initially available in just a few countries, but the 2015 ITU conference approved a worldwide frequency allocation.

Credit: youtube.com, 10 meters beacon list is great for propagation and dx purpose

The Federal Communications Commission (FCC) made 60 meters available to General, Advanced, and Amateur Extra U.S. amateur radio license classes in 2003. The NTIA emphasizes that hams planning to operate on 60 meters must assure their signal is transmitted on the channel center frequency.

Here's a breakdown of the center frequencies and corresponding 'dial' frequencies for the 60-meter band:

Radio amateurs in the U.S. have access to five discrete channels on a secondary basis, limited to an effective radiated power (ERP) of 100 W PEP.

Ham Radio

The 60-meter band is a popular choice among ham radio operators, and for good reason. It's a relatively new allocation, having been opened up for amateur use in 2013.

The band is allocated from 5351 to 5413 kHz, and it's a great option for operators who want to make long-distance contacts. This is because the 60-meter band is capable of propagation over long distances, making it ideal for DXing.

Suggestion: S Meter

Credit: youtube.com, Yaesu FT-991 & A, hidden 60 m band and overview

One of the benefits of the 60-meter band is its ability to be used for both voice and digital modes. In fact, the band has been used for everything from voice communications to digital modes like PSK31 and RTTY.

The 60-meter band is also relatively quiet, with less interference from other users compared to other bands. This makes it easier to make contacts and communicate effectively.

Overall, the 60-meter band is a great option for ham radio operators who want to make long-distance contacts and try out new modes and techniques.

Power and ERP

The power limit for amateurs in Canada is 100 watts ERP, which means 100 watts of power radiated from the antenna, not the transceiver itself.

You need to factor in the gain of your antenna to ensure you don't exceed this limit. If your antenna has more gain than a dipole, you must reduce your power accordingly.

In Canada, we have a relatively generous power limit compared to other countries. Most countries limit amateurs to running 15 watts EIRP, which is 15 watts into an isotropic radiator.

To stay within the limit, you must use the upper band on 60 meters, as per the convention. This is a specific requirement for SSB operation on this frequency band.

It's worth noting that some countries have more restrictive power limits, while others have more generous limits.

Frequently Asked Questions

What band is 6M?

The 6-meter band is a portion of the VHF radio spectrum allocated for amateur radio use, spanning 50.000-54.000 MHz. Also known as 6M, it's characterized by an average signal wavelength of 6 meters.

Claire Beier

Senior Writer

Claire Beier is a seasoned writer with a passion for creating informative and engaging content. With a keen eye for detail and a talent for simplifying complex concepts, Claire has established herself as a go-to expert in the field of web development. Her articles on HTML elements have been widely praised for their clarity and accessibility.

Love What You Read? Stay Updated!

Join our community for insights, tips, and more.